1. MMDVM_Bridge.ini

[General]
Callsign=JF2ANH
Id=440201001
Timeout=180
Duplex=0

[Info]
RXFrequency=430720000
TXFrequency=430720000
Power=1
Latitude=41.7333
Longitude=-50.3999
Height=0
Location=Iceberg, North Atlantic
Description=MMDVM_Bridge
URL=https://groups.io/g/DVSwitch

[Log]
# Logging levels, 0=No logging, 1=Debug, 2=Message, 3=Info, 4=Warning, 5=Error, 6=Fatal
DisplayLevel=1
FileLevel=0
FilePath=/var/log/mmdvm
FileRoot=MMDVM_Bridge

[DMR Id Lookup]
File=/var/lib/mmdvm/DMRIds.dat
Time=24

[NXDN Id Lookup]
File=/var/lib/mmdvm/NXDN.csv
Time=24

[Modem]
Port=/dev/null
RSSIMappingFile=RSSI.dat
Trace=0
Debug=0

[D-Star]
Enable=0
Module=C

[DMR]
Enable=1
ColorCode=1
EmbeddedLCOnly=1
DumpTAData=0

[System Fusion]
Enable=1

[P25]
Enable=0
NAC=293

[NXDN]
Enable=0
RAN=1
Id=12345

[D-Star Network]
Enable=0
GatewayAddress=127.0.0.1
GatewayPort=20010
LocalPort=20011
Debug=0

[DMR Network]
Enable=1
Address=3108.repeater.net           #BM Master DDNS Name 
Port=62031
Jitter=360
Local=62032
Password=passw0rd
Slot1=0
Slot2=1
Debug=0

[System Fusion Network]
Enable=1
LocalAddress=127.0.0.1
LocalPort=0
GatewayAddress=xrf098.mydns.jp      #changeYSFReflector DDNS Name 
GatewayPort=42000
Debug=0

[P25 Network]
Enable=0
GatewayAddress=127.0.0.1
GatewayPort=42020
LocalPort=32010
Debug=0

[NXDN Network]
Enable=0
#LocalAddress=127.0.0.1
Debug=0
LocalPort=14021
GatewayAddress=127.0.0.1
GatewayPort=14020

2,DVSwitch.ini

; MMDVM_Bridge export / import configuration file.
;   This file should be placed along side of MMDVM_Bridge or it can be
;   supplied as a path on the MMDVM_BRIDGE environment variable.

; Configure the Quantar Repeater Partner
; Note that the TX and RX ports are already reversed for MMDVM_Bridge <--> Quantar_Bridge
[QUANTAR]
logFilePath = /var/log/Quantar_Bridge.log
Address = 127.0.0.1             ; Address to send AMBE TLV frames to (export)
TXPort = 34103                  ; Port to send AMBE TLV frames to (export)
RXPort = 34100                  ; Port to listen on (import)
quantarPort = 1994              ; HDLC frames To/From the Quantar repeater
logLevel = 2                    ; Show messages and above 0=No logging, 1=Debug, 2=Message, 3=Info, 4=Warning, 5=Error, 6=Fatal
debug = 0                       ; Debug 0 = off, 1 = on (adds lots of additional messages)

; Configure the DMR Partner
; Audio format is AMBE 72 bit
[DMR]
Address = 127.0.0.1             ; Address to send AMBE TLV frames to (export)
TXPort = 31100                  ; Port to send AMBE TLV frames to (export)
RXPort = 31103                  ; Port to listen on (import)
Slot = 2                        ; Export slot

; Configure the D-Star Partner
; Audio format is AMBE 48 bit (DSAMBE)
[DSTAR]
Address = 127.0.0.1             ; Address to send AMBE TLV frames to (export)
TXPort = 32100                  ; Port to send AMBE TLV frames to (export)
RXPort = 32103                  ; Port to listen on (import)
FallbackID = 4402010            ; In case we can not find a valid DMR id in the database, export this one
ExportTG = 9                    ; Which TG to export
Slot = 2                        ; Export slot

; Configure the NXDN Partner
; Audio format is AMBE 72 bit
[NXDN]
Address = 127.0.0.1             ; Address to send AMBE TLV frames to (export)
TXPort = 33100                  ; Port to send AMBE TLV frames to (export)
RXPort = 33103                  ; Port to listen on (import)
FallbackID = 1234567            ; In case we can not find a valid DMR id in the database, export this one
NXDNFallbackID  = 12345         ; Use this ID when the input DMR ID is not found in the database
Translate = 1234=4321           ; Translate NXDN TG < -- > DMR TG (bidirectional)
Slot = 2                        ; Export slot

; Configure the P25 Partner
; Audio format is IMBE 88 bit
[P25]
Address = 127.0.0.1             ; Address to send AMBE TLV frames to (export)
TXPort = 34100                  ; Port to send AMBE TLV frames to (export)
RXPort = 34103                  ; Port to listen on (import)
Slot = 2                        ; Export slot

; Configure the Yaesu Fusion Partner
; Audio format is AMBE 72 bit
; Audio format is IMBE 88 bit
[YSF]
Address = 127.0.0.1          ; Address to send AMBE TLV frames to (export)
TXPort = 35100                  ; Port to send AMBE TLV frames to (export)
RXPort = 35103                  ; Port to listen on (import)
FallbackID = 4402010            ; In case we can not find a valid DMR id in the database, export this one
ExportTG = 9                    ; Which TG to export
Slot = 2                        ; Export slot

3,Analog_Bridge.ini

; Analog_Bridge configuration file.
;   This file should be placed in either /etc or it can be
;   supplied as a path on the Analog_Bridge command line.

; The best way to think of this file is that there are two main sections, the USRP (analog audio) and
; AMBE_AUDIO (compressed audio).  Analog_Bridge will take everything sent to the USRP port and
; encode it for transmission on the AMBE_AUDIO port.  The encoder will use the format defined in ambeMode.
; As you might expect, the reverse direction is defined too.

; Analog_Bridge supports include files. More on this later...
include = dvsm.macro
; include = asl.macro

; General Section describes settings for Analog_Bridge itself.
[GENERAL]
logLevel = 2                            ; Show messages and above 0=No logging, 1=Debug, 2=Message, 3=Info, 4=Warning, 5=Error, 6=Fatal

; Metadata management
subscriberFile = /var/lib/dvswitch/subscriber_ids.csv   ; DMR ID to callsign lookup data
exportMetadata = true                   ; Export metadata to USRP partner (transcode setups require this)

; General vocoder setup information
decoderFallBack = true                  ; Allow software AMBE decoding if a hardware decoder is not found
useEmulator = true                      ; Use the MD380 AMBE emulator for AMBE72 (DMR/YSFN/NXDN)
emulatorAddress = 127.0.0.1:2470        ; IP address and port of the md380 server

; Information for xx_Bridge (Where xx is MMDVM, Quantar, HB, IPSC)
[AMBE_AUDIO]
address = 127.0.0.1                     ; IP address of xx_Bridge
txPort = 31103                          ; Transmit TLV frames to partner on this port
rxPort = 31100                          ; Listen for TLV frames from partner on this port
ambeMode = DMR                          ; DMR, DMR_IPSC, DSTAR, NXDN, P25, YSFN, YSFW (encode PCM to this format)
minTxTimeMS = 2500                      ; Minimum time in MS for hang delay (0-10000)

; The metadata below is used when ASL is the source since it does not have any concept of digital modes
gatewayDmrId = 4402010                        ; ID to use when transmitting from Analog_Bridge
repeaterID = 440201001                          ; ID of source repeater
txTg = 9                                ; TG to use for all frames sent from Analog_Bridge -> xx_Bridge
txTs = 2                                ; Slot to use for frames sent from Analog_Bridge -> xx_Bridge
colorCode = 1                           ; Color Code to assign DMR frames

; Information for USRP channel driver.  This interface uses PCM to transfer audio information
; There are two typical configurations, ASL and Transcode.  ASL (AllstarLink) is for analog clients connected
; to a digital network.  Transcode is when Analog_Bridge actually points its PCM interfaces back at itself, 
; causing a TLV <-- (pcm <--> pcm) --> TLV type of architecture.
;   When using ASL, this matches the rpt.conf ASL file with a setting like:
;   rxchannel = usrp/127.0.0.1:34001:32001
;   When Transcoding, make two ini files and set txPort equal to the other instance rxPort (crossover).  Launch
;   each instance with its own ini file.
[USRP]
address = 127.0.0.1                     ; IP address of USRP partner (Allstar/Asterisk or another Analog_Bridge)
txPort = 50111                          ; Transmit USRP frames on this port
rxPort = 50111
aslAudio = AUDIO_USE_GAIN               ; Add New Line
agcGain = 2.5                           ; Add New Line If you need to adjust the DMR -> ASL audio, change
dmrAudio = AUDIO_USE_GAIN               ; Add New Line
dmrGain = 1.0                           ; Add New Line If you need to adjust the ASL -> DMR audio, change

                          ; Listen for USRP frames on this port
;usrpAudio = AUDIO_UNITY                 ; Audio to ASL (AUDIO_UNITY, AUDIO_USE_AGC, AUDIO_USE_GAIN)
;usrpGain = 1.10                         ; Gain (in db) of the AGC filter
;tlvAudio = AUDIO_UNITY                  ; Audio from ASL (AUDIO_UNITY, AUDIO_USE_GAIN, AUDIO_BPF)
;tlvGain = 0.35                          ; Gain factor of audio from ASL (0.0-1.0)

[MACROS]

; Where the macros are
; xxxx=yyyy
; xxxx is the dial string to match
; yyyy is the command line to execute

; xxxx must be preceded by a *
; xxxx can be any string (alphanumeric)
; yyyy is the command to execute
; yyyy will replace xxxx in the dial string
; arguments follow the macro name with a # delimiter

; For example using macro "5678" above would look like:
; *5678#9876

; Which would invoke:
; echo 9876

; Information for DV3000 hardware decoder
;   There are two configuration modes: IP (AMBEServer) and serial (direct connect hardware)
;   Use top server and port if using AMBEServer
;   Use bottom server/port and serial = true if using the DV3000u (thumbdv)
;   Did you run AMBETest4.py before using this?
[DV3000]
address = 127.0.0.1                    ; IP address of AMBEServer
rxPort = 2460                         ; Port of AMBEServer
; address = /dev/ttyUSB0              ; Device of DV3000U on this machine
; baud = 460800                       ; Baud rate of the dongle (230400 or 460800)
; serial = true                       ; Use serial=true for direct connect or serial=false for AMBEServer

----------------- END ----------------------------------